Verified 7-Degree Right-Hand Profile
Exact Tool No. 45810 combines the specified 7-degree angle with right-hand usage for Incra® and stair-stringer applications.
Amana Tool Carbide-Tipped 7° Right-Hand Stair-Tread Dovetail Router Bit 3/4-Inch Diameter x 7/8-Inch Cutting Height x 1/2-Inch Shank
CA$999.99
Out of stock
SKU
45810
Product Type
Carbide-Tipped Stair-Tread Dovetail Router Bit
Family / Category
7 Degree Dovetail Router Bits
Angle / Usage
7° · Right hand
Cutting Diameter
3/4 inch
Cutting Height
7/8 inch
Shank / Overall
1/2-inch shank · 2-5/8-inch overall length
Flutes / Material
2 flutes · Carbide tipped
Applications
Certain Incra® applications,stair-tread dovetails,and stair-stringer joinery
Digital Resources
SKU-specific DXF and PDF profile files available
Carbide-Tipped Z2
7-Degree Right-Hand Stair-Tread Dovetail Bit
Stair-Tread Dovetail Bit
Amana Tool 45810 is the exact carbide-tipped right-hand dovetail router bit with a 7-degree angle, 3/4-inch diameter, 7/8-inch cutting height, 1/2-inch shank, 2-5/8-inch overall length, and two flutes for certain Incra® applications and stair-stringer joinery.
7°Angle (a°)
3/4 inDiameter (D)
7/8 inCutting Height (B)
2Flutes
Stair-Tread Dovetail Bit
A two-flute carbide-tipped dovetail router bit with a verified 7-degree right-hand profile. Its dedicated official page identifies the exact Tool No. as 45810.
Amana ToolCarbide TippedRight HandSKU 45810
Amana Tool lists Incra® as the application for this exact SKU and states that the 7-degree angle is also used for stair-stringer cutting. Confirm a compatible 1/2-inch collet and the required right-hand configuration.
Main Product Description
Amana Tool 45810 is the exact Tool No. shown on its dedicated official product page. The labelled specification block confirms a 7-degree angle, 3/4-inch diameter, 7/8-inch cutting height, 1/2-inch shank, 2-5/8-inch overall length, right-hand usage, two flutes, and Incra® application.
The official title identifies this carbide-tipped profile as a stair-tread right-hand dovetail bit. Amana Tool states that certain Incra® applications require a 7-degree dovetail bit and that this angle is also used when cutting stair stringers.
The product page provides SKU-specific DXF and PDF profile resources. It also notes that Keller™ system bits are supplied with shank-mounted bearings; because the exact 45810 specification does not list a bearing, Keller™ compatibility should not be assumed without confirming the required bearing configuration.
Technical Specifications
7 Degree Dovetail Router Bits · SKU 45810
- Amana Tool
- Carbide-Tipped Stair-Tread Right-Hand Dovetail Router Bit
- 45810
- 7 Degree Dovetail Router Bits
- 7 Degree Dovetail Router Bits
- 7°
- 3/4 inch
- 7/8 inch
- 1/2 inch
- 2-5/8 inches
- Right Hand
- 2
- Application: Incra® · Active Cutting Material: Carbide Tipped · Additional Application: Stair-Stringer Cutting · Digital Profile Resources: SKU-Specific DXF · PDF
- Amana Tool lists Incra® as the application for this exact SKU and states that the 7-degree angle is also used for stair-stringer cutting. Confirm a compatible 1/2-inch collet and the required right-hand configuration.
Best Fit Applications
Certain Incra® Applications
Stair-Stringer Joinery
Stair-Tread Dovetails
Right-Hand Dovetail Routing
7-Degree Dovetail Joinery
Product Highlights
Carbide-Tipped Z2 Geometry
Two carbide-tipped flutes form the verified profile with a 3/4-inch diameter and 7/8-inch cutting height.
SKU-Specific Profile Resources
The official product page provides dedicated DXF and PDF profile resources corresponding to exact Tool No. 45810.
Compatibility & Installation Notes
Confirm exact Tool No. 45810, right-hand usage, a compatible 1/2-inch collet, adequate cutter clearance, secure workholding, and the required Incra® profile. Amana Tool notes that Keller™ system bits use shank-mounted bearings; the exact 45810 specification does not list a bearing, so do not assume Keller™ compatibility. Follow Amana Tool and machine-manufacturer safety documentation.
Verified 7-Degree Right-Hand Geometry for Dovetail and Stair Joinery
Amana Tool 45810 combines a 7-degree profile, 3/4-inch diameter, 7/8-inch cutting height, 1/2-inch shank, 2-5/8-inch overall length, right-hand usage, and two carbide-tipped flutes.
The exact official page identifies Incra® as its application and supports the 7-degree geometry for stair-stringer cutting, subject to confirmed system fit and machine-safety requirements.