Application consistency
Coverage needs to be repeatable
The two spreading rollers are designed for precise, uniform application across one or both panel faces.
Orma i213
ORMA MACCHINE
I213 Two-roller glue spreader for one- or two-sided panel application and through-feed integration
The ORMA I213 uses two 185 mm spreading rollers to apply adhesive to both panel faces or a single face. Its 1300 mm working width, 100 mm maximum roller clearance and 18 m/min running speed are paired with roller-support shock absorbers that accommodate thickness variation and help compensate panel parallelism differences.
2 spreading rollers1300 mm working width100 mm roller clearance185 mm roller diameter18 m/min feed speedthrough-feed line capable
Production problem
Manual or inconsistent glue application can bottleneck panel layup before pressing and make adhesive coverage harder to standardize.
Application mechanism
Two grooved anti-acid rubber spreading rollers can coat both panel faces or one face only.
Line value
I213 can be used in through-feed lines, allowing it to sit between panel preparation and pressing.
Two spreading rollers
One- or two-sided spread
1300 mm working width
18 m/min standard feed
Integrated roller washing tube
Through-feed integration
Start with the manufacturing problem
Glue spreading has to control coverage, panel thickness and feed without becoming the bottleneck before the press.
I213 is a process machine between panel preparation and pressing. Selection starts with panel width/thickness, one- or two-sided adhesive application, adhesive/process compatibility, required feed behavior and how the spreader connects to upstream and downstream handling.
Thickness accommodation
Panel thickness varies
Roller-support shock absorbers let the roller system accommodate panel-thickness differences within 5 mm and help compensate parallelism variation.
Ownership
Cleaning has to fit production
Quick-removal distribution tanks, an extractable collection tank and a perforated wash tube are integrated into the machine architecture.
Line balance
Feed must match the press cell
I213 can be used in through-feed lines; practical cell output still depends on the surrounding line.
Application fit
For flat panels within the I213 roller-clearance envelope where controlled adhesive spreading is required before pressing or assembly.
The I213 supports adhesive spreading on both panel surfaces or one surface only. Final adhesive compatibility, coat requirement and cleaning practice still need to match the actual adhesive system.
Strong fit
Panel lamination / pressing cells
Strong fit where panels need a controlled adhesive layer before cold or hot pressing.
Strong fit
One-sided glue application
The machine can spread on a single panel face.
Strong fit
Two-sided glue application
The same two-roller architecture supports simultaneous application to both panel faces.
Integration fit
Through-feed layouts
I213 can be used in through-feed lines.
Non-fit cue
Panels above 100 mm clearance
Maximum clearance between the rollers is 100 mm; thicker workpieces require another process or application review.
Different ORMA route
Different glue-spreader architecture
Applications outside the I213 working envelope require a different glue-spreading solution.
Select the glue-spreading process from the panel backwards
Define the substrate, adhesive coverage and downstream press before selecting the spreader setup.
This keeps roller speed and one-/two-sided application tied to a real manufacturing process.
Define the panel
Length, width, thickness, surface condition and typical thickness variation.
Define adhesive process
Adhesive family, required one- or two-sided coating, spread target and approved cleanup method.
Check working envelope
Confirm 1300 mm width and 100 mm maximum roller clearance against the real panel.
Set feed strategy
Use the standard 18 m/min basis or qualify the optional variable-speed route where needed.
Balance the line
Match panel preparation, glue spreading, layup and downstream pressing/handling.
Machine architecture / work cycle
Feed the panel between two spreading rollers, control adhesive distribution, then send the coated panel onward.
The I213 is not a press and does not cure the adhesive. Its role is controlled roller application and transfer into the next production step.
Roller architecture
Two spreading rollers
Both rollers use special anti-acid rubber and are ground and grooved for adhesive spreading.
Application mode
One- or two-face spreading
The roller arrangement supports coating on both panel surfaces or a single surface.
Panel handling
Automatic thickness accommodation
Shock absorbers on the roller supports allow automatic movement to handle thickness variation within 5 mm.
Drive
Chain-driven roller rotation
Roller rotation uses a chain drive with a self-adjusting pinion.
Glue-spreading capability
The roller, dosing and wash architecture is designed around repeatable application and service access.
The roller, dosing and wash components are designed for repeatable glue application, cleanup access and ongoing service.
Upper spreading roller
Ø185 mm
Panel path
One- or two-sided application
Lower spreading roller
Ø185 mm
Quick-removal distribution tanks · extractable glue / wash-water collection tank · perforated washing tube
Roller and wash detail
Wear-resistant rollers with quick-removal supporting components.
The anti-acid rubber roller covering is described as thick enough to permit up to 6-7 regrindings. Distribution tanks are ground/rectified galvanized sheet and designed for quick extraction, while the lower collection tank for glue and roller-washing water is also extractable.
Final adhesive and cleaning compatibility is confirmed against the actual glue system and production process.
Technical specifications
I213 machine data.
Core I213 dimensions, roller data, feed speed, working height and control information for application planning.
| Specification | I213 value | Imperial / notes |
|---|---|---|
| Roller count | 2 spreading rollers | Two-roller architecture |
| Working width | 1300 mm | 51.18 in |
| Maximum clearance between rollers | 100 mm | 3.94 in |
| Roller diameter | 185 mm | 7.28 in |
| Running speed | 18 m/min | 59.1 ft/min |
| Coaxial reducer gear / motor | 0.37 HP | ~0.28 kW |
| Net weight | 340 kg | ~750 lb |
| Overall dimensions | 200 × 78 × 135 cm | 78.74 × 30.71 × 53.15 in |
| Working height | 800 mm | 31.50 in |
| Control voltage | 24 V control board | Start / stop pushbuttons + warning light |
Panel / roller envelope
Width and roller clearance are the primary dimensional gates.
The 5 mm shock-absorber condition describes thickness variation accommodation; maximum panel clearance between the rollers remains 100 mm.
1300 mm51.18 in working width
100 mm3.94 in maximum clearance between rollers
185 mm7.28 in roller diameter
800 mm31.50 in working height
within 5 mmThickness-difference condition accommodated by the shock-absorber roller supports
Roller / dosing framework
Application quality is controlled by roller condition, dosing hardware and panel presentation.
Glue spread, viscosity, temperature and cure parameters are qualified to the actual adhesive and panel process.
Spreading rollers
Special anti-acid rubber, ground and grooved, with a wear layer suitable for up to 6-7 regrindings.
panel feed → roller contact → one- or two-sided adhesive application
2spreading rollers
185 mmroller diameter
18 m/minstandard feed speed
Glue dosing
Rectified distribution tanks in galvanized sheet meter adhesive uniformly and are designed for quick extraction for cleaning.
Viscosity, coat weight, glue temperature and cure time are set from the approved adhesive and panel process.
Controls / operator workflow
Simple start/stop control supports a dedicated glue-spreading station or line component.
I213 uses a straightforward 24 V start/stop control arrangement for dedicated glue-spreading or line integration.
Control
24 V control board
The control board has start and stop pushbuttons plus a warning lamp.
Electrical
Motor protection
The electrical plant is housed in a water-tight enclosure with switching and thermal motor protection.
Feed
Standard feed speed
Standard running speed is 18 m/min.
Control scope
Straightforward machine control
The machine uses the documented 24 V control-board architecture rather than a production-programming interface.
Handling
Panel-thickness accommodation
Shock absorbers on the roller supports help the rollers adapt automatically to the documented thickness-variation condition.
Integration
Through-feed capable
The machine can be used in through-feed lines.
Glue / washing / safety architecture
Cleanup and guarding are built into the machine concept.
Wash hardware and machine safety devices are part of the I213 operating architecture; cleanup procedures remain tied to the approved adhesive process.
Washing
Perforated roller-washing tube
A bored/perforated wash tube supplies water during roller washing.
Cleanup
Extractable collection tank
The galvanized collection tank receives glue and roller-washing water and can be removed for cleaning.
Dosing service
Quick-removal distribution tanks
The glue-distribution tanks are designed for rapid extraction for cleaning.
Guarding
Roller / tank guards
Safety protection is provided around the rollers and glue-distribution tanks.
Safety
Front + rear emergency bars
Double emergency bars are documented at the front and rear of the machine.
Process boundary
Cleaning process remains adhesive-specific
Water-washing hardware supports roller cleanup; the actual cleaning process follows the adhesive supplier requirements and applicable machine documentation.
Feed-rate / throughput framework
18 m/min is a feed speed, not a guaranteed panel-output rate.
Panel length, gaps between parts, loading, downstream press capacity and optional speed control all influence practical production.
Machine speed
18 m/min standard running speed
Standard machine running speed.
Output context
Panel length changes pieces/minute
The same line speed produces different piece counts with different panel lengths and spacing.
Line balance
Downstream press can become the limit
A faster glue spreader does not increase cell output if layup or pressing cannot accept the flow.
Throughput discipline
Practical output depends on the line
Finished-panel output depends on panel length, spacing, handling, layup and downstream press capacity.
Ownership / service / changeover
Roller condition and cleanup planning are central to owning a glue spreader.
Roller condition, tank access and cleanup planning are central to maintaining consistent adhesive application.
Roller life
Rollers can be reground
The rubber thickness permits up to 6-7 regrindings.
Service access
Rollers are quick to remove
The spreading rollers are described as easy and quick to disassemble.
Cleanup access
Tanks are removable
Distribution and collection tanks are designed for extraction to simplify cleaning access.
Safety
Qualified electrical / mechanical service
Drive, guards, emergency bars and electrical components are serviced using applicable machine documentation and qualified personnel.
Through-feed line integration
I213 can sit directly between panel preparation and the press cell.
Through-feed use still requires the line design to match panel width, working height, feed direction, part spacing and downstream capacity.
Prepare panel
Surface preparation and panel staging to the approved adhesive process.
Feed I213
Present panels within the 1300 mm width and 100 mm roller-clearance envelope.
Spread adhesive
Apply to one or both faces through the two spreading rollers.
Lay up / assemble
Add veneer, laminate, facing or mating panel according to the manufacturing process.
Press downstream
Transfer into the selected cold/hot press or other qualified assembly process.
Options / valid configuration
Available I213 options for speed, mobility and washing.
Configure the option package around line speed, machine mobility and cleanup requirements.
Option
Manual washer with brushes
Available as an I213 option.
Option
4 swivel wheels
Four casters are available; two include brakes.
Option
0.5 HP variable-speed drive
Optional Motovariator range: 5-26 m/min.
Business-case framework
Value I213 around coverage consistency, handling and line balance.
Build the business case from the existing spreading process, actual handling time, adhesive usage, rejects and downstream line balance.
Time study
Glue-spreading time
Measure setup, application, transfer and cleanup across representative panels.
Product mix
Panel mix
Track width, thickness and one-/two-sided application requirements.
Process
Adhesive usage / quality
Measure actual coat target, rejects and rework with the approved adhesive process.
System value
Press-cell balance
Compare the 18 m/min spreader feed capability against layup and press cycle capacity.
Application data package
Send the panel dimensions, adhesive process and downstream press.
These inputs establish whether the I213 envelope and feed/control options fit the cell.
Dimensions
Panels
Minimum/maximum width, thickness, length and typical thickness variation.
Glue
Adhesive
Adhesive family, one-/two-sided application and required coat/process specification.
Flow
Production flow
Feed rate, panels/shift, spacing, upstream handling and downstream press/layup.
Project
Site / options
Electrical service, desired variable-speed range, mobility/washer option and available floor space.
Complete at quotation
Close the I213 application and option package.
Your complete ORMA I213 proposal defines the 1300 mm two-roller configuration, panel thickness/clearance, one- or two-sided glue process, actual adhesive compatibility, feed-speed requirement, standard or optional variable-speed arrangement, washer/mobility options, electrical configuration, line-entry/exit interfaces, guarding/safety package, shipping data, commissioning, training and role in the complete panel-lamination or pressing process.
I213 / I-213 model
1300 mm working width
100 mm roller clearance
One- / two-sided spreading
Adhesive process
18 m/min or optional variable speed
Washer / caster option
Electrical configuration
Through-feed integration
Commissioning / training
I213 contains powered rollers, moving panel stock and industrial electrical equipment. Operation, cleaning, adjustment and service follow applicable machine documentation, the adhesive supplier’s requirements and qualified workplace procedures. Guards and emergency devices are not bypassed.
I213 FAQ
Questions that determine whether the two-roller spreader fits the cell.
The primary gates are panel width/thickness, one-/two-sided coating, adhesive process and required feed behavior.
How many spreading rollers does I213 use?
Two. ORMA identifies I213/I-213 as a two-roller glue spreader.
What is the working width?
1300 mm, approximately 51.18 in.
What is the maximum clearance between rollers?
100 mm, approximately 3.94 in.
Can it spread glue on both sides?
Yes. The two-roller architecture supports adhesive application to both panel faces or a single face.
What is the standard running speed?
18 m/min, approximately 59.1 ft/min.
Does it have variable speed?
An optional 0.5 HP Motovariator provides a 5-26 m/min variable-speed range.
Can I213 be used in a through-feed line?
Yes. I213 can be used in through-feed lines.
How does it handle small thickness differences?
Shock absorbers on the roller supports allow automatic roller movement for panel-thickness differences within 5 mm and help compensate parallelism variation.
What cleanup hardware is built in?
Quick-removal distribution tanks, an extractable glue/wash-water collection tank and a perforated roller-washing tube support cleanup and service access.
What determines practical panel output?
Practical panel output depends on panel length, spacing, handling, layup and downstream press capacity; the machine’s standard running speed is 18 m/min.
ORMA I213 application review
Send the panel dimensions and glue process.
Titan can qualify the I213 working width, roller clearance, one-/two-sided application, feed-speed option and through-feed role against the actual panel-lamination or pressing process.
Useful inputs:panel width/length/thickness, thickness variation, adhesive family, one- or two-sided coat requirement, existing spread method, desired line speed, panels/shift, downstream press, electrical service and option requirements.